Description
‑ Power Supply: Powered by Procontrol P13 rack back‑plane bus
‑ Power Consumption: approx 12 W
‑ Mechanical Structure: Eurocard plug‑in board for Procontrol P13 rack, metal front panel, back‑plane bus connector, front‑panel communication ports
‑ On‑board Resources: 32‑bit dedicated communication processor, flash memory, RAM buffer, multi‑media signal conditioning circuit, back‑plane bus interface, module self‑diagnosis unit
‑ Communication Interface: Internal dedicated back‑plane bus for interaction with CPU; front‑panel optical fiber interfaces and electrical communication ports
‑ Galvanic Isolation: Galvanic isolation between external communication ports and rack internal logic bus
‑ Supported Physical Media: ST‑type optical fiber, electrical serial interface
‑ Supported Protocols: IEC 60870‑5‑103, internal P13 plant‑bus protocol, Modbus related protocol
‑ Status LED Indicators: Power indicator, Module Fault indicator, communication link / activity status LEDs
‑ Weight: approx 1.1 kg
‑ Acts as communication gateway for Procontrol P13 rack, completes data exchange between rack main CPU and external automation equipment.
‑ Real‑time protocol conversion: converts internal back‑plane bus data into external communication protocol frames, and reversely parses external downlink commands and transmits to CPU.
‑ Supports cyclic process data transmission, non‑cyclic parameter configuration, fault alarm and event message uploading.
‑ Communication channel diagnosis: monitors link status, signal loss, frame error, reports communication fault information to main processor.
‑ Module self‑diagnosis detects power‑supply deviation, internal processor running exception, back‑plane bus communication fault, uploads module‑level fault alarm.
‑ Cannot work independently; must be installed inside Procontrol P13 rack and cooperate with CPU, power‑supply and I/O modules. 1MRB150077R1B is hardware revision variant of 500CIM05 series; pin‑compatible within 500CIM05 revision family, cannot be directly interchanged with other series communication boards.
‑ Continuously monitors communication link status, module power‑supply and internal hardware health. Detected faults activate fault LED and send fault word to main CPU.
‑ No local numerical display; communication status, link alarms and fault codes are read via commissioning software or upper‑level HMI workstation.
‑ Module hardware failure will cause loss of external communication for the whole rack; local rack internal control logic still keeps running normally if CPU and power‑supply work properly.
‑ Back‑plane connector: connects to Procontrol P13 internal back‑plane bus for data exchange with CPU and other plug‑in modules.
‑ Front‑panel ports: optical fiber and electrical communication interfaces for connection to upper‑level system or remote bay units.
‑ Mounting: Plug‑in installation inside Procontrol P13 system rack
‑ Operating Temperature: ‑20 °C ~ +60 °C
‑ Storage Temperature: −40 °C ~ +70 °C
‑ Relative Humidity: 5‑95 %RH, non‑condensing
‑ Protection Class: IP20 (cabinet internal)
- 500CIM05 communication interface module (1MRB150077R1B)
Complementary parts: Procontrol P13 rack and back‑plane, system CPU module, rack power‑supply unit, optical fiber / shielded communication cables, Procontrol P13 commissioning software.
‑ Power off the whole rack before inserting or removing this communication module. Optical fiber wiring shall avoid excessive bending; electrical communication wiring adopts shielded cables with single‑end shield grounding to restrain electromagnetic interference.
‑ For spare‑part replacement: Verify complete part number 1MRB150077R1B, confirm firmware version matching requirement. After replacement, confirm back‑plane bus identification, download communication configuration parameters, verify link connection, data transceiving and fault‑reporting function. Firmware mismatch will result in communication abnormal.
‑ Module hardware fault causes loss of external communication channel of the rack.
Generator‑transformer control cabinets of thermal / hydro power plants; ABB Procontrol P13 automation system; industrial spare‑part replacement for system external communication gateway.
- Procontrol P13 platform dedicated high‑performance communication gateway module, supports optical fiber and electrical dual‑media, multiple industry standard protocols, realizes interconnection between local rack and upper‑level system / remote devices.
- Built‑in communication link diagnosis function, convenient for field communication fault locating.
- Galvanic isolation between external communication side and rack internal logic bus, strong anti‑interference capability for power‑plant harsh electromagnetic environment.
- Realizes bidirectional protocol conversion, transmits process data, events and alarms between main processor and external system.
- Standard Eurocard rack‑mount plug‑in structure, easy installation and on‑site maintenance.
Reviews
There are no reviews yet.