ABB DYPS154C 61430001-YP MOSFET Digital Output Module

Description

Hardware & Electrical Specifications

• Model：DYPS154C
• Part Number：61430001‑YP
• Module Type：Solid‑state MOSFET digital output module (sink type)
• Channel count：16 output channels
• Isolation architecture：Every 4 channels form one isolated group; opto‑coupler galvanic isolation between groups; isolation between field circuit and back‑plane logic bus
• Field load voltage：DC 12 V ~ 30 V
• Per‑channel continuous output current：1 A DC
• Per‑channel peak current：3 A, maximum duration ≤100 ms
• Total maximum module load current：8 A (all 16 channels activated simultaneously)
• Output response time：≤100 μs
• Typical on‑state resistance：≤0.1 Ω
• Channel‑level protection：
  • Over‑current limiting：1.2 A ±0.1 A, auto‑recovery after fault removal
  • Short‑circuit protection：tolerate continuous short‑circuit, no hardware damage, auto‑reset
  • Reverse‑polarity protection：tolerate reverse DC 30 V wiring
  • Over‑voltage clamping：max transient 36 V DC
• Logic power supply：24 V DC supplied by rack back‑plane
• Max power consumption：4.8 W
• Insulation strength：2500 V AC between field side and logic back‑plane side
• Insulation resistance：＞100 MΩ @ 500 V DC

Environmental Specifications

• Operating temperature：0 ℃ ~ +55 ℃
• Storage temperature：‑20 ℃ ~ +70 ℃
• Relative humidity：5%‑95% non‑condensing
• Protection degree：IP20 (inside control cabinet)
• EMC compliance：IEC 61000‑6‑2 industrial immunity standard
• Certifications：CE

Mechanical Data

• Installation：Plug‑in slot mounting on Advant OCS standard rack, mechanical latch locking
• Terminal：Screw‑type removable terminal block, suitable for 0.75 mm²‑2.5 mm² copper conductors
• Terminal tightening torque：0.6‑1.0 N·m
• Dimension：120 mm × 110 mm × 45 mm
• Weight：approx 0.33 kg

Main Functions

1. 16‑channel solid‑state DC output：MOSFET sink output, no mechanical contact abrasion, support frequent high‑speed switching. Drive DC solenoid valves, small intermediate relays, cabinet indicator lamps, alarm buzzers, field proximity sensor power supply loads。
2. Group‑wise galvanic isolation：4 channels per isolation group, effectively suppress cross‑group interference when mixing different field power domains.
3. Full channel self‑diagnosis：Detect output short‑circuit, over‑current, load open‑circuit, internal circuit fault. Fault code with channel number is uploaded to DCS controller for alarm.
4. Per‑channel LED status indicator
   • Green ON：output channel activated
   • Green OFF：output channel de‑activated
   • Red flash：channel fault (short‑circuit / over‑current / open‑load)
5. Software configurable parameters via Control Builder：output invert logic, fault latch / auto‑reset mode, open‑circuit diagnosis enable / disable.
6. Auto‑recovery protection：No fuse required; after short‑circuit or over‑current fault disappears, channel automatically resumes operation without module replacement, reduce maintenance workload。

Installation & Wiring Requirements

1. Insert into Advant OCS standard rack slot, lock mechanical latch; back‑plane bus completes power supply and communication automatically.
2. Maintain cabinet ventilation, avoid conductive dust, corrosive gas and strong electromagnetic field.
3. For inductive DC loads (solenoid coil, relay coil), connect free‑wheeling diode in parallel at load side to absorb back‑EMF, protect MOSFET output circuit.
4. Strictly follow current rating: single channel shall not exceed 1 A continuous current; total module load shall not exceed 8 A.
5. Cabinet protective grounding must comply with industrial control grounding specification to guarantee isolation performance and anti‑interference capability.
6. Do not apply AC voltage to output channels, this module is only for DC load application.