Description
‑ Power Supply: Powered by excitation rack back‑plane bus
‑ Power Consumption: approx 7.5 W
‑ Mechanical Structure: Eurocard plug‑in board for UNITROL rack, metal front panel, back‑plane bus connector, multi‑channel serial communication terminal interface
‑ On‑board Resources: multi‑channel serial transceiver circuit, protocol processing unit, signal isolation circuit, surge‑suppression protection unit, back‑plane bus controller, module self‑diagnosis circuit, conformal‑coating protection layer
‑ Communication Interface: Internal dedicated back‑plane bus for excitation main‑control board; external RS485/RS232 serial channels
‑ Galvanic Isolation: Galvanic isolation for external serial communication channels, isolation rating 2500 VAC
‑ Supported Protocol: excitation proprietary communication protocol, supports connecting HMI, synchronizing device and upper monitoring system
‑ Status LED Indicators: Power indicator, Module Fault indicator, communication sending‑receiving status LED
‑ Weight: approx 0.90 kg
‑ Acts as serial communication gateway for UNITROL excitation rack, receives data instruction from external HMI and upper‑level monitoring system, forwards to excitation main‑control board; uploads generator operating parameters, alarm and fault data from main‑control board to external devices.
‑ Supports data interaction with external synchronization equipment, transmits synchronization‑related measuring data and control commands.
‑ Completes serial signal isolation, level conversion and surge suppression, restrains interference introduced by long‑distance field communication cables.
‑ Module self‑diagnosis monitors rack power‑supply, transceiver circuit and back‑plane bus communication; detects communication channel abnormality and hardware fault, uploads module‑level fault‑alarm information to main‑control board. Conformal‑coating improves long‑term reliability under high‑humidity site condition.
‑ Cannot run independently; must be installed inside UNITROL excitation rack and cooperate with excitation main‑control board. HENF315125R1 is hardware revision variant of E3EC series; pin‑compatible within E3EC revision family, cannot directly interchange with other series excitation boards.
‑ Continuously monitors communication channel status, module power‑supply and internal hardware health. Detected faults activate fault LED and send fault word to excitation main controller.
‑ No local numerical display; communication status and fault codes are read via excitation commissioning tool or upper‑level HMI workstation.
‑ Module hardware failure will cause loss of external serial communication function; excitation AVR regulation and protection logic still run normally, but remote parameter setting and data monitoring cannot be performed.
‑ Back‑plane connector: connects to excitation rack internal bus, exchanges data and diagnostic status with main‑control board.
‑ Serial communication terminal interface: wiring terminals for HMI, synchronization device and upper‑system communication shielded cables.
‑ Mounting: Plug‑in installation inside UNITROL excitation cabinet rack
‑ Operating Temperature: ‑20 °C ~ +60 °C
‑ Storage Temperature：−40 °C ~ +70 °C
‑ Relative Humidity: 5‑95 %RH, non‑condensing
‑ Protection Class: IP20 (cabinet internal)
- E3EC serial communication interface board (HENF315125R1)
Complementary parts: UNITROL excitation rack and back‑plane, excitation main‑control board, shielded communication cables, excitation commissioning software.
‑ Power off the whole excitation rack before inserting or removing this board. Serial communication wiring must adopt shielded cables with single‑end shield grounding; strictly distinguish different communication equipment wiring ports.
‑ For spare‑part replacement: Verify complete part number HENF315125R1. After replacement, confirm back‑plane bus identification, verify data transceiving and fault‑reporting function. Hardware revision mismatch will lead to communication incompatibility.
‑ Module hardware fault will result in failure of external serial data interaction.
Thermal‑power and hydro‑power generator excitation cabinets; ABB UNITROL generator excitation system; industrial spare‑part replacement for excitation serial communication gateway unit.
- UNITROL excitation system dedicated E3EC serial communication interface board, realizes data exchange between excitation main‑control unit and HMI, synchronizing device and upper‑level monitoring system, hardware variant HENF315125R1.
- Conformal‑coating processing, adapts to power‑plant high‑humidity and corrosive harsh site environment.
- External communication channel adopts opto‑coupler galvanic isolation, strong anti‑interference capability for long‑distance field communication.
- Built‑in communication self‑diagnosis function, convenient for field communication‑loop fault location.
- Standard Eurocard rack‑mount plug‑in structure, convenient installation and on‑site maintenance.
Reviews
There are no reviews yet.