Description
‑ Power Supply：Power supplied by Harmony rack back‑plane, 5VDC back‑plane logic power supply
‑ Mechanical Structure：Rack plug‑in module for Symphony Harmony rack；overall weight approx 0.42kg
‑ On‑board Resources：MC68701 8‑bit microprocessor, 2KB EPROM, 128‑byte RAM, 16‑bit internal timer, signal conditioning and comparator circuit, self‑diagnosis circuit。
‑ Communication Interface：Internal INFI90 rack back‑plane module bus, communicate with BRC/MFP controller, configured by function code 145。
‑ Galvanic Isolation：Galvanic isolation between field pulse input side and system back‑plane side.
‑ Core Function：Single‑channel pulse signal conditioning, pulse counting, period and frequency calculation, turbine rotating‑speed conversion, hardware self‑diagnosis, upload speed process value to DCS controller。
‑ Protection：Input over‑voltage protection for pulse input channel.
‑ Status LED Indicators：Module run LED, fault diagnostic LED.
‑ Weight：approx 0.42kg
‑ IMFCS01 is one‑channel dedicated frequency counting module, input frequency range 1Hz‑12.5kHz, adapt to sine‑wave / square‑wave pulse signal output by magnetic pickup speed probe.
‑ On‑board microprocessor completes pulse edge detection, count and period measurement, calculate frequency and rotating‑speed value, transmit digital process data to DCS controller through rack back‑plane bus, support turbine speed closed‑loop control cooperating with hydraulic servo module IMHSS03.
‑ Support configurable pulse trigger threshold, avoid measuring failure caused by sensor signal amplitude deviation. Built‑in hardware self‑diagnosis, detect module hardware fault and input signal abnormal, alarm information upload to operator station.
‑ Installed on Symphony Harmony standard rack, must use matched special terminal unit to connect magnetic pickup sensor, cannot work independently.
Difference compared with ordinary AI module：IMFCS01 is intelligent special measuring module, hardware completes frequency counting, not simple analog sampling; ordinary analog input module cannot realize high‑precision pulse speed measurement.
‑ Receive field pulse signal from rotating‑equipment speed sensor, complete frequency‑speed conversion locally, transmit process value to upper‑level BRC/MFP controller.
‑ Realize module hardware fault diagnosis; signal abnormal alarm upload to DCS system.
‑ No independent closed‑loop control function, speed‑regulating control algorithm is executed by upper‑level controller.
‑ Back‑plane：Rack internal back‑plane module bus for data communication and module power supply.
‑ External interfaces：Connect magnetic pickup speed probe via matched terminal unit.
‑ Mounting：Plug‑in installation on Symphony Harmony standard rack
‑ Operating Temperature：‑20 ℃ ~ +60 ℃
‑ Storage Temperature：‑40 ℃ ~ +85 ℃
‑ Relative Humidity：5‑95 %RH, non‑condensing
‑ Pollution degree：Degree 2
‑ Protection Class：IP20, cabinet‑internal installation.
- IMFCS01 frequency counter slave module（3BSE008582R1）
Complementary parts: Symphony Harmony rack, matched terminal unit, BRC / MFP series controller, magnetic pickup speed sensor, system rack power supply, IMHSS03 hydraulic servo module (turbine control loop).
‑ Insert module into correct slot of Harmony rack, tighten front‑panel fixing screws to ensure reliable back‑plane connector contact.
‑ Field magnetic pickup sensor wiring adopts supporting terminal unit; reasonably set pulse trigger threshold according to actual output amplitude of speed probe, prevent zero‑speed measuring fault caused by threshold mismatch.
‑ Module replacement recommends power‑off operation. After replacement, download function‑code 145 configuration, verify speed measuring value consistency with local on‑site instrument.
‑ Input signal voltage shall not exceed module specification limit, avoid hardware damage.
Power plant steam turbine / gas turbine control cabinets; Symphony INFI90 DCS rotating‑equipment speed measurement spare‑part; cooperate with hydraulic servo module for turbine speed closed‑loop control.
- ABB Symphony Harmony IMFCS01 frequency counter slave module (3BSE008582R1), single‑channel intelligent pulse / frequency special measuring module for turbine speed measurement。
- Frequency measuring range 1Hz‑12.5kHz, on‑board micro‑processor realizes pulse count, period and rotating‑speed calculation, support configurable trigger threshold。
- Galvanic isolation between field side and system side, complete hardware self‑diagnosis and fault alarm upload function.
- Rack plug‑in structure, cooperate with special terminal unit for magnetic pickup sensor wiring, cabinet‑internal IP20 application.
- Belongs to INFI90 DCS special‑function I/O subsystem, data interaction through rack back‑plane bus, match function code 145 for configuration.
- Discontinued legacy DCS spare‑part, used for old‑system maintenance and retrofit projects。
Reviews
There are no reviews yet.