GE IC200PWR001G VersaMax Backplane Power Supply Module

Description

Hardware & Electrical Specifications

‑ Model：IC200PWR001G ‑ Part Number：IC200PWR001G ‑ Module Type：VersaMax Backplane Power Supply Module ‑ Mounting：Snap‑on to CPU / NIU / IC200PWB001 booster carrier, DIN‑rail mounting ‑ Input power：18‑30 VDC, nominal 24 VDC, max input power 11 W ‑ Hold‑up time：10 ms minimum at nominal 24 VDC input ‑ Inrush current：20 A@24 VDC (6 ms max), 25 A@30 VDC (6 ms max) ‑ Output：   • +5 VDC and +3.3 VDC backplane power   • Total output current：max 1.5 A   • 3.3 VDC max 0.25 A; 5 VDC current = total current minus 3.3 VDC consumption ‑ Terminals：Screw terminal block for DC‑24V input ‑ Compatible carrier：CPU base, NIU base, IC200PWB001 power booster carrier ‑ PCB treatment：Conformal coated for dust‑moisture‑corrosion resistance ‑ On‑board protection：Reverse‑polarity protection, overload current‑limiting, short‑circuit shutdown, thermal protection; DC‑ internally connected to protective frame ground ‑ Compatibility note：Cannot run standalone; must match VersaMax carrier base; calculate total backplane current consumption before commissioning; full power‑loop test mandatory after replacement.

Environmental Specifications

‑ Operating temperature：0 ℃ ~ +60 ℃ ‑ Storage temperature：‑40 ℃ ~ +85 ℃ ‑ Relative humidity：5%‑95% non‑condensing ‑ Installation location：Indoor industrial control cabinet ‑ EMC compliance：IEC 61000‑6‑2 ‑ Certifications：CE, UL Class I Div 2 hazardous‑location certification

Mechanical Data

‑ Weight：approx 0.12 kg ‑ Dimension：Standard VersaMax power‑supply module form‑factor (39 × 133 × 49 mm) ‑ Handling note：ESD‑sensitive power circuit, anti‑static wrist‑strap mandatory during handling ‑ Terminal tightening torque：0.6‑1.0 N·m

Main Functions

1. Accepts external 24 VDC field power input, converts and supplies stable 5 VDC / 3.3 VDC power to VersaMax backplane for CPU, network interface and I/O modules.
2. Works as main station power supply when attached to CPU/NIU carrier; acts as auxiliary booster power on IC200PWB001 for racks with high‑current I/O load.
3. Built‑in hardware protection: reverse‑connection, short‑circuit, overload and over‑temperature protection to prevent damage to downstream backplane devices.
4. LED status indication:   ‑ Green OK LED：Input power normal and output healthy

Installation & Wiring Requirements

1. Cut off external 24 VDC input power before replacement. Hot‑swap is forbidden. Strict anti‑static protection when handling module.
2. Snap module onto CPU / NIU / booster carrier, rotate locking latch to lock position for reliable mechanical and electrical contact.
3. 24 VDC input wiring strictly follow GE VersaMax hardware manual GFK‑1504K; DC‑ must connect to cabinet protective ground; external MOV surge suppression is recommended at power input terminal; separate power cables from low‑signal analog cables.
4. Complete protective grounding according to GE system specification.
5. After replacement：power‑on step‑by‑step, verify OK LED status, measure backplane rail voltage, check all downstream I/O module power‑on status.
6. Replacement note: Calculate total backplane current consumption to avoid overload; full power‑supply‑loop simulation test mandatory before unit put‑into‑service.