GE IC695ETM001 PACSystems RX3i Ethernet Interface Module

Description

Hardware & Electrical Specifications

‑ Model: IC695ETM001 ‑ Part Number: IC695ETM001 ‑ Module Type: RX3i Ethernet Interface Module, occupies 1 single slot on universal backplane ‑ Mounting: Any slot on RX3i universal backplane IC695CHS series; supports main rack and expansion rack installation ‑ Backplane power consumption:  • +3.3 VDC: 400 mA nominal  • +5 VDC: 200 mA nominal ‑ Ethernet processor: 200 MHz ‑ Communication buffer memory: 512 KB ‑ Ethernet interfaces:  • 2 × shielded RJ45 10/100 Base‑TX, auto‑negotiation, auto‑MDI‑X, half‑duplex / full‑duplex; internal integrated network switch for daisy‑chaining; max cable length 100 m for CAT5 cableMoore Auto… ‑ Serial interface:  • Station‑Manager RS‑232 (9‑pin female D‑sub), baud rate range:1200‑115200 bps, local diagnostics and module configuration only ‑ Network protocols: SRTP, Modbus‑TCP Client/Server, EGD, SNMP, HTTP ‑ IP configuration: Static IP or DHCP client ‑ Concurrent connections: Maximum 32 simultaneous Ethernet connections ‑ Hot‑swap: Supported under system power‑on (firmware V2.51 or higher required)honeywell-… ‑ Local control: Recessed Ethernet Restart push‑button for module firmware soft reset without rack power‑cycleManualsLib ‑ Diagnostics: Module self‑test, LAN link status, port speed/duplex status, channel error counter, web‑based diagnostic page ‑ PCB treatment: Conformal coated for dust, moisture and corrosion resistance ‑ Compatibility note: Compatible with IC695 CPU315, CPU320, CRU320, also works with CPE‑series CPUs. Hot‑swap operation only for this I/O‑type module; CPU hot‑swap remains forbidden. Verify total backplane power budget before installation. Full module configuration download and network connectivity test must be performed after replacement.

Environmental Specifications

‑ Operating temperature: 0 ℃ ~ +60 ℃ ‑ Storage temperature: ‑40 ℃ ~ +85 ℃ ‑ Relative humidity: 5%‑95% non‑condensing ‑ Installation location: Indoor control cabinet, IP20 protection class ‑ EMC compliance: IEC 61000‑6‑2 ‑ Certifications: CE, UL Class I Div 2 hazardous‑location certification

Mechanical Data

‑ Weight: approx 0.51 kg (1.13 lbs) ‑ Dimension: RX3i single‑slot module form‑factor ‑ Handling note: ESD‑sensitive communication circuitry. Use CAT5 or higher shielded twisted‑pair Ethernet cables. RS‑232 port is for station‑manager maintenance only, cannot be used for user Modbus‑RTU application.

Main Functions

1. Provides high‑speed Ethernet network access for RX3i CPU, supports programming download, SCADA host communication, Modbus‑TCP field device connection, peer‑to‑peer EGD data exchange between PACSystems controllers.
2. Built‑in two‑port Ethernet switch enables daisy‑chain wiring without external industrial switch, simplifies cabinet network cabling.
3. RS‑232 Station‑Manager port for local onsite module diagnosis, IP setup and status monitoring without Ethernet network.
4. Supports web‑page diagnostic via HTTP for quick network fault inspection.
5. Front‑panel LED indicators:   ‑ Green MOD OK: Module hardware normal status   ‑ Red LAN FLT: Ethernet network / configuration fault   ‑ Port A / Port B: Link / activity LED for each RJ45 port   ‑ SPEED: 100 Mbps speed indicator

Installation & Wiring Requirements

1. Cut off rack power supply for initial installation; hot‑swap is allowed for module replacement if firmware version meets requirement. Apply ESD protection during module handling.
2. Insert IC695ETM001 into RX3i backplane single slot and engage locking latch.
3. Network wiring comply with GE RX3i hardware manual. Use shielded CAT5e / CAT6 twisted‑pair Ethernet cable. For daisy‑chain topology, terminate the last device of chain with proper network terminator. Reliable protective‑ground connection is required. RS‑232 station‑manager port uses dedicated null‑modem cable.
4. After replacement: Power‑on rack power, check front‑panel LED status. Download hardware configuration, assign IP address settings. Complete network link test, Modbus‑TCP and EGD communication verification.
5. Replacement note: Confirm firmware version; verify IP address conflict risk in plant network. Full‑system commissioning test is mandatory before putting into service.